MARYLAND METRICS -- THREAD DATA CHART: Metric Thread -- Coarse Pitch. Nominal British Pipe Thread ( Whitworth Form) -- Parallel (BSPP/BSPF) -- (G).

per inch, while a 1/4-28 (UNF fine) thread has the same nominal major diameter but 28 threads per inch. Metric thread specifications are different because the thread pitch is defined by the distance between each thread in mm instead of threads per inch. For example, an M12x1.75 (coarse) thread has a 1.75mm pitch, while an M12x1.50 (fine) thread

Chart No 1 - Whitworth Threads Whitworth Form Threads (55 Deg Thread Angle) Dimensions in Inches except where stated Thread Form Data Tapping Drill Clearance Drill Diameter O/Diameter Core Pitch Depth Radius Effective Dia T.P.I Dec / Met / Frac Dec / Met / Frac 1/8" 0.1250 0.0930 0.0250 0.0160 0.0034 0.1090 40 0.1004 - 2.55mm 0.1299 - 3.30mm

British Thread (British Standard Whitworth) -- Coarse Pitch. Nominal Size Ww. Thread Form Type. Major Diameter mm d=D. Pitch mm p. Threads per inch tpi. Pitch Diameter mm d2=D2. Minor Diameter Male Thd. d3. Thread Height H1.

1) PF and PT threads are functionally interchangeable with BSPP and BSPT threads, respectively. These are old designations. They are being replaced with G (for 

Thread Form r = Basic Radius = * 137329 p h = Basic Depth of Thread = *640327 p p = Pitch = 1/t.p.i. (Threads per Inch) ISO 228, DIN 259, BS2779, JIS B0202 In Japan this thread is known as (PF) Use prefix G for parallel thread. Example: G1/2 11 /

ANSI/ ASME INTERNAL Screw Thread Size Chart. All units are in inches. Unified Screw Threads per. ANSI/ASME B1.1-1989 (R2001), R2001) Nomenclature, are used. Acceptability criteria are described in ANSI/ASME B1.3M-1992 (R2001). Note: This screw chart is not comprehensive of all available standard threads as provided by the standard.

1/4″ (6mm) from thread diameter measurement for nominal pipe size. Pitch is Threads Per Inch (TPI). “Gas”, “R” & “G” also refer to BSP. “Male Iron 

Metric Thread 10 12 14 16 18 20 22 24 26 27 30 33 36 42 48 M 10x1.0 M 12x1.5 M 14x1.5 M 16x1.5 M 18x1.5 M 20x1.5 M 22x1.5 M 24x1.5 M 26x1.5 M 27x2.0 M 30x2.0 M 33x2.0 M 36x2.0 M 42x2.0 M 48x2.0 15/16 - 12 THREAD CHARTS • JIC - SAE • Metric/International VISIT US AT BRENNANINC.COM

Whitworth's new standard specified a 55° thread angle and a thread depth of 0.640327p and a radius of 0.137329p. Where p is the pitch. The thread pitch increases with the diameter in steps specified on a chart. The Whitworth thread system was later to be adopted as a British Standard to become British Standard Whitworth (BSW).

G/R/RP - Whitworth thread (BSPP/BSPT) View the table G = BSPP ISO 228 (DIN 259) R/Rp/Rc = BSPT ISO 7 (DIN 2999 replaced by EN10226) UNC/UNF - Unified national thread. View the table UNC ANSI B1.1 UNF ASNI B1.1. Drawings of other threads. Conversion factor. Download the types of thread document.

British Standard Pipe BSP thread chart, BSP thread chart showing TPI and drill sizes. BSPP / BSPT B RITISH S TANDARD P IPE P ARALLEL / B RITISH S TANDARD P IPE T APER

No. of Threads/Inch. UNC UNF UNEF UNM NPT. METRIC. Dia. Thread Pitch in mm mm. Coarse. Fine. THREAD SIZE COMPARISON CHART.

Fastener and Screw / Bolt Design, Formula and Calculations Internal Pipe Threads per. ISO 228-1, Pipe threads where pressure-tight joints are not made by the threads. These pipe threads are also known as Whitworth pipe threads. Where: D = Major Dia.internal thread D 1 = Minor Dia.internal thread D 2 = Pitch diameter internal thread

POB 1778 Greer, SC 29652 414 West Poinsett Street Greer, SC 29650 [email protected] Ph: 864-848-3993 www.traskinst.com Fax: 864-848-9569 G-SERIES PIPE THREAD (BRITISH

British Standard Pipe (BSP) has been use as standard in plum and pipe fittings. There are two types of BSP Thread available. Parallel threads & Taper 

29 rows · Feb 12,  · 3 Controlled Root Radius on External Thread. 4 Controlled Root Radius on Internal Thread. 5 N vs. UN. 6 STI Gage Before or After Inserted. 7 STI Gage Tolerances. 8

Determination - Thread Types G or R or BSP G or R (Whitworth) or BSP (British Standard Pipe) Thread Cylindrical threads which are mainly used in countries with imperial system. The size of e. g. R 3/4" does not stand for a diameter. Thus the corresponding size has to be determined according to charts.

BSP Thread Size Outside Diameter mm / inch TPI 1/16 Inch BSP 7.7 mm / 0.304" 28 1/8 Inch BSP 9.7 mm / 0.383" 28 1/4 Inch BSP 13.16 mm / 0.518" 19

External thread th. Designation of thread. Number of threads in 25.4 mm. Pitch P. Height of thread h. major d = D. pitch d2 = D2. minor d1 = D1. Lower deviation.

There are two types of BSP threads; - BSPP - male thread are both (also known as G) - BSPT - thread is parallel and the male thread is tapered (also know as R/Rp) (the thread can also be tapered it is then Rc, these are fairly rare to find).