Inverter Duty Motors Frames : 90S to 355LX Rating (kW) : 0.37 to 315.0 Poles : 2, 4, 6, 8 Mountings : B3, B5, B14 & combinations Protection : IP55 Enclosure : Force Cooled Roller Table Motors Frames : 112M to 160L Rating (kW) : 0.75 to 7.5 Poles : 4, 6, 8

The /FG flange-mounted motor design is used for mounting the motor onto the SEW gear unit for the DR.. series. The flange dimensions are implemented according 

1/9 · Frame size variants (extract) In addition to the standard numbering system for frames, there are some standardized variations that are denoted by the following suffixes to the NEMA

Frame Size. A. B. H. D. E. 63. 100 mm. 80 mm. 63 mm. 11 mm. 23 mm. 71. 112 mm. 90 mm. 71 mm. 14 mm. 30 mm. 80. 125 mm. 100 mm. 80 mm. 19 mm. 40 mm.

MOTOR MOUNTING EXPLANATION E D M M P N D S S P N D P N D E B3 - Foot Mounted Motor B5 - flange ('D' flange) The flange diameter is bigger than the motor frame diameter. Welkon.net Motor Frame Sizes - MROSupply.com Type "C" face (flange) mounted motor. They have threaded mounting holes in the face of the motor. D.

Motors whose frame size output classification does not corres- pond with the standard series according to NEMA MG1-12. • Flange-mounting motors.

The following are dimensional size charts for standard electric motor NEMA standard Type D Flange Footless Motors Standardized motor dimensions are established by the National Electrical Manufacturers Association (NEMA) - are tabulated below and apply to all base-mounted motors listed herein that carry a NEMA frame designation

FLANGE MOUNTED MOTORS 'B' TYPE[B5]. FRAME. SIZE. FLANGE ±0.3 M. N. P MAX. S. T MAX. LA. LD MIN. L. LC. LO. AD. AC. ØD,ØDA. E. F,FA. GA,GC. GB. D3.

C-Face dimensions: • Hole circle diameter (M) • Centering diameter (N) • Outer diameter (P) • Thread dimensions (S) • Number of bores (K) Example SEW designation Dimensions For motor size FC 5.875" M = 5.875" DR. 71, DR. 80 and DR.90 N = 4.5" P = 6.5" S = 3/8"-16 K = 4 FC 7.25" M = 7.25" DR.90 and DR.100 N = 8.5" P = 8.875" S = 1/2"-13 K = 4 Not

Horizontal foot mounting (B3 ) as per IS :1231. BEARING SIZE CHART Bearing clearance-Motors upto 132M FRAME have normal clearance bearings.

Frame Foot Mounted Shaft B5 Flange B14 Face A B1 H D E DB EG LA M N P S T 63 100mm 3.94" 80mm 3.15" -63mm AA dimensions shown in chart are Baldor typical values meeting or exceeding NEMA. Please check motor drawing for actual dimensions. Frame L449T is not included in this chart. Please refer to the Large AC motor chart, or to the specific

B3 - Foot Mounted Motor B5 - flange (’D’ flange) The flange diameter is bigger than the motor frame diameter. The holes are not tapped. BASIC DIMENSIONS SHAFT KEY 315 frame 132

Base of 56HZ frame motors has holes and slots to match NEMA 56, 56H, 143T and 145T mounting dimensions. @ Certain NEMA 56Z frame motors have 1/2" x 1 1/2" long shaft with 3/64" flat. These exceptions are noted in the General Catalog. & Dimension "V" is shaft length available for coupling, pinion or pulley hub - this is a minimum value.

frame shaft foot mount size m n p c m n p c m n p c dia center hight iec metric electric motor flange dimensions b5 b14a b14b. b14 flange all torque torque industrial power transmission solutions www.alltorque.com.au . author: all torque preston created date:

Industrial performance motors Sizes 63 to 400, 0.12 to 630 kW ABB reserves the right to change the design, technical specification and dimensions without prior notice. *) *) H = foot/flange-mounted, motor with feet, IM 2001 IM IM 2031 IM 2051 IM 2061 IM 2071 term.box top large flange S = foot/flange-mounted, term.box RHS T = foot

THE METRIC MOTOR SPECIALISTS" B5 and B14 flange dimensions Frame Increase Reduction List "C" Flange B14 63 71 80 90 100 112 56 63 71 80 90 64 64 72 88 128 128 71/80 80/90 90/100 100/112 132 132 Frame Size Flange Mount List M N P N P M M N P "D" Flange B5 "C" Flange B14 "C" Flange B14 . Title: CEGcatalog.pdf

Dimensions Frame Sizes 56 - 315 D FLANGE MOUNTED C FACE MOUNTED FOOT MOUNTED Brook Crompton - Electric Motors 800 668-6779 - www.brookcromptonna.com FRAME D E 2E 2F BA H AA AB C BS CBH CBW 56 3.50 2.43 4.87 3.0 2.75 0.34

IEC Quick Reference Chart ; 180M 180L, 279 mm, 241 mm 279 mm, 180 mm, 48 mm ; 200L 200M, 318 mm, 267 mm 305 mm, 200 mm, 55 mm 

Frame Size. Pole. Grease lifetime up to CT 40ºC. Grease for permanent lubrication bearing. 80~225. 2, 4, 6. 20000 hours (B3 mounting).

a dc motor or generator c "c" flange mounting on drive end ** d e shaft dimensions for elevator motors in frames larger than the 326u frame h frame with an "f" dimension larger than a frame without (small framed motors) j jet pump motors jm jp "c"-face mounted close coupling pump - packed pump k sump pump motor lp & lph "p" flange mounting

Motors are in IEC frame sizes with fixing dimensions provided by IS 1231/IS 2223 for foot and flange mounted motors respectively.